Do You Have To Use The Fiberglass In Devcon Home Repair Kit

I will admit in the past I have paid over $1,500 to become a tub surround replaced which could have been stock-still with this solution. Since then I accept learned a few things and ane of those things is how to repair holes in a fiberglass environs ensuring a watertight surface and something that isn't an eyesore.

For this project, I used Devcon Fiberglass, Porcelain, and Plastic Repair Kit, which was about a $13 investment, plus a few other tools I already had in my garage (run into below). While the procedure is fairly easy, it does have a piddling patience when it comes to sanding the surface for a shine finish.

Notation: You can also utilise the epoxy on cracks and other small knicks in your tub surrounds – it's not simply for screw holes.

If yous'd rather watch than read, cheque out the YouTube video beneath.👇

Tools:

Devcon Repair Kit (White/Almond) ** this works on fiberglass, porcelain, and plastic
Sandpaper (Assorted)
Painter's Tape
one-gallon ziplock bag (cutting it into foursquare sheets)
Toothpicks

DISCLAIMER: This blog contains affiliate links, which means that if you lot click on one of the production links, I'll receive a small commission.

How to Patch and Filling Screw Holes in a Fiberglass Bathtub – seven Steps

For this example, I was patching screw holes left backside after I removed a glass shower door from my tub/shower surroundings. Overall I had a full of 6 holes to fill up and I ordered ii kits and did ane side (three holes) at a time. This Playlist shows the whole project on our YouTube Aqueduct.

1. Section Off Surface area with Painter'due south Record

Use Painter's Tape Around Screw Holes — _{Securing Area with Painter'southward Tape}

Before you do anything with the epoxy kit, prep the surface past sectioning off the holes with painter's tape. I like to make a box shape around each hole. This will contain the epoxy when information technology runs and it will assist subsequently on when y'all start sanding the expanse. Likewise, ensure the surface has no loose pieces and is completely clean of any oils or residuum.

2. Squeeze & Mix the Epoxy

With the Devcon Repair Kit, printing the epoxy from the lesser of the parcel. Go along to mix information technology with your hands for about 45 seconds to ensure you accept a complete mix. (I then added the almond color to the epoxy since my bathtub is almond-colored.)

Warning: You lot only have about 5 minutes of working time before the epoxy starts to firm upward so make sure you have everything ready once you get to this step.

3. Make full in Screw Holes with Epoxy

Filling in holes with epoxy — _{Filling in screw holes with epoxy}

Using the toothpick, place the epoxy straight in the spiral holes. Information technology's ok if it drips out a little. You'll exist calculation more epoxy in the next stride. Since my holes were small I merely used epoxy if you lot have a larger hole and need additional strength the kit will come with some cobweb mesh to embrace the larger pigsty and provide the boosted strength once dry.

four. Brush Actress Epoxy on Holes

Epoxy Over the Holes — _{Brushing extra epoxy on the holes}

Castor and spread out the epoxy. Exist sure to build it upwards and then you have a fiddling extra. Don't worry, I know it looks gunky! Yous'll use the ziplock plastic sheets to shine information technology out in the next step.

five. Place Plastic on the Epoxy and Tap Over Them

Plastic Sheets Over Holes — _{Tapping out air bubbles over the spiral holes}

Place the plastic sheet over the holes filled with epoxy. And then, tap over the area to get the air bubbles out and smooth out the surface. Don't worry in one case everything is dry (I let it sit for 2-three hours) the ziplock bad volition come right off without any issue.

half-dozen. Sandpaper Over the Holes

Remove the plastic sail and sand over the epoxy with 60 dust sandpaper. This is the roughest sandpaper I used and is meant to speedily remove the backlog epoxy. Practise not sand the surface of your tub environs with this sandpaper or it volition remove the finish.

7. Pare Tape Off & Sandpaper Again

_{This is what the area will look like when the tape is off}

Peel the painter's record off and go dorsum over the epoxy with more than sandpaper. Switch to 320 grit sandpaper and continue to sand. Finally, switch once again to 600 dust and continue to sand until polish.

Pro tip: Add together a little water to the surface every bit y'all're sanding for the smoothest finish.

The Wrap Upward

Smooth surface of the bathtub without holes — _{The finished upshot: a await at the smooth surface after the area is patched upward and sanded}

Overall, I was pleasantly surprised with the Devcon Epoxy Bathtub Repair Kit. The almond finish matched surprisingly well and I was happy with the affluent end. I as well concluded upwardly putting a drapery rod up, which fabricated the patched-up holes barely noticeable. But let me know what you think. If yous've tried this project, experience free to share what worked for yous in the comments below… or let me know what you'd do differently.

Watch more than videos of home repair projects at the Everyday Home Repairs Youtube Channel .